Nudura manufactures a range of accessories for a variety of ICF applications. Click on each accessory to watch a video or visit our YOUTUBE channel to see the entire playlist.
The Transition Bracket allows two different form of widths to be connected. Primary use is to create a ledge to support brick or a floor system.
The Vertical Joint Clip is designed to connect the form at the vertical joints. It replaces having to tie wire or tape forms together while providing a solid connection using a minimal amount of labor to install.
Surface Mount Brick Tie and Pintle. – Designed to be fastened with two Nudura Hex head Screws anywhere on the Nudura fastening strip. This tie will accept Nudura Pintels and other smaller dimension pintels. tested to meet ASTM D754 (USA) and CSA-A370 (CAN) std. requirements for masonry anchors.
FORM-LOCK is used to maintain wall straightness. Other uses include wall alignment for vertical stack joints. Each bundle has 100’ (30m) of FORM-LOCK.
Nudura’s Rebar Clip is specially designed to securely support horizontal reinforcement in the bottom web of the Nudura form during the concrete pour. This clip eliminates the need to tie wire or zip-tie the reinforcement bar in place when it is required to be pulled up into the bottom of the web.
Nudura RPD Dovetail Insert is designed the slide into the dovetails on the inside of the form to support vertical reinforcement where support does not already exist.
Fiber Tape is used to provide additional EPS support for field cut forms that have more than 4" (100mm) of EPS extending past the last web, brick ledge forms in the corner conditions, and radius panel.
The metal handle Foam Gun is compatible with the Nudura Low Expansion Foam 24oz (680g) cans. The Nudura Low Expansion Foam can be used for a number of different tasks on site.
The Foam Gun Cleaner is used to clean the internal chamber of the foam gun from any hardened foam. Also used on the external surfaces for cleaning the guns.
The Low Expansion Foam is compatible with Nudura's Expanded Polystyrene (EPS) foam. It can be used for several different tasks on-site, including foaming the forms to the slab or footing, between vertical joints, securing service penetrations, and as insulation around openings.
The Membrane Primer is designed for use with Nudura's self-adhesive waterproof membranes. This polymer emulsion-based primer is available in a 19L (5 gallons) pail, with a coverage of approximately 650-2000 ft2 (60-190m2) of wall area per container. The Nudura Membrane Primer can help improve the adhesion of Nudura's Waterproofing Membrane in specific areas.
The Peel & Stick Waterproofing Membrane is used for below grade damp proofing of the Nudura walls. Other uses for the Waterproofing Membrane include drain flashings around window and door openings and brick ledge through wall flashings. Available in summer and winter grades.
The Fiber Mesh gets embedded into the parge coat to give it strength.
The Rebar Cutter is used for cutting and bending reinforcing steel used in the Nudura wall system. It comes with two cutting heads that will cut up to #5 (15M), reinforcing steel. The rollers used for bending the steel are capable of handling up to a #5 (15M) bar.
The 4-Way Web Connector allows two or more insert webs to be connected and used with the panel system to create wider form sizes. It also can be used to create forms of different shapes and sizes. Increased design flexibility.
The #10 screw can be used to connect the Nudura Alignment System to the forms. Other uses include attachment of strapping or buck material to concrete. Available in 2" (50mm), 2 1/2" (64mm) and 3" (76mm) lengths. Two 1/4" (6mm), nut drivers, included per pail.
The Bit Kit is a 10 piece quick change kit that keeps all the bits together in one convenient spot. The kit includes five 1/4" magnetic nut setters which can be used with any of Nudura's Hex Head Screws with Steel Flat washers, as well as five #2 red square driver bits. It is available in packages of 12.
Click resources below to download:Product Catalogue
We’re committed to supporting homeowners and design professionals who are interested in or use our products. We’re always happy to help and provide more information.